 |
|
|
|
| Front panel controls | (4) Line position controls (2 X and 2 Y) multi-turn optical encoders |
| Front panel switches | (11 total) Display on / off, Position Lock (2), Line Enable (4), Black/White, Independent / Relative mode, Box / Line mode, Power |
| Remote port | EIA-232 (RS-232) 8 pin mini-DIN connector |
| Data format | MicroImage Control Language |
| X axis line width | 81.5 nS (NTSC/RS170), approx 70nS (PAL/CCIR) |
| Y axis line width | 2 scan lines (Field Mode), 1 scan line (Frame Mode) |
| Line Resolution |
NTSC/RS170 - 640 x
480 Frame Mode, 640 x 240 Field Mode PAL/CCIR - 768 x 576 Frame Mode, 768 x 288 Field Mode |
| Adjustment range | 98% of raster minimum |
| Sync system | NTSC/RS170 or PAL/CCIR, rear panel switchable (Serial Number 10026 and later. See note below) |
| Genlock | Precision Phase Locked Loop (PLL), square pixel |
| Input Levels | |
| composite | 1.0Vpp composite, 75 ohm |
| S-Video | NTSC - 1.0Vpp (Y),
0.286Vpp burst (C), 75 ohm PAL - 1.0Vpp (Y), 0.300Vpp burst (C), 75 ohm |
| RGB | 0.7Vpp non-comp / 1.0VPP Comp, 75 ohm |
| Sync | 0.3-4Vpp, 75 ohm |
| Output Levels | |
| composite, S-Video,RGB |
Same as respective
input, +/-5% into 75 Ohm |
| Sync | Same as input level, up to 2Vpp. |
| Connectors | |
| composite/RGB/Sync | BNC Female |
| S-Video | 4 pin mini-DIN Female (Standard S-Video connector) |
| RS232 | 8 pin mini-DIN Female |
| Bandwidth | Greater than 30 Mhz |
| Temperature | |
| Operating | 0 deg - 40 deg C (32 deg - 104 deg F) |
| Storage | -40 deg - 60 deg C (-40 deg - 140 deg F) |
| Humidity | |
| Operating | 10% - 90% (non-condensing) |
| Storage | 5% ~ 95% (non-condensing) |
| Power |
Voltage 110 - 125VAC, 50 / 60Hz (+/-5VDC and +12VDC optional, consult factory) |
| Consumption | 12W |
| Size
|
8.5" (W) x
7.2" (D) x 2.25" (H) 216mm (W) x 183mm (D) x 57mm (H) |
| Weight | 2 lbs. 4 oz. (1021g) |
Manufactured in the USA by MicroImage Video Systems |
|
NOTE: Units with serial numbers 10001 through 10025 do NOT support PAL/CCIR operation. They will only support NTSC/RS170 signals. Dual support is a new feature added to the CL741 units for serial numbers 10026 and later. If you have an older unit, it can be upgraded at the MicroImage factory with the new firmware to support PAL/CCIR standards. Please contact MicroImage Engineering for additional information. Please give us your serial number when contacting us. Thank you. |
© 1995-2004
MicroImage Video Systems, a division of World Video Sales Co., Inc.
All rights reserved. Specifications subject to change without notice. 01/05/04
Problems with this site? Contact the webmaster
w w w . m i v s . c o m
