h3-specifications.gif (1694 bytes)
PXS311 Single Camera Comparison Controller

Front Switches (9) Power, Camera A, Camera B, Split L/R, Split T/B, Fade, Difference, Freeze and Exchange
Front Controls (1) Split position/Fade ratio control
Rear Controls (4) 4 position DIP switch for options
1 - NTSC/PAL Select
2 - Center Split Mode select
3 - B input Composite/S-Video select (must be set to same as A below)
4 - A input Composite/S-Video select
Rear Connections (5) Power, composite input A, S-Video input A, composite output and S-Video output
(RS232 connection optional)
Internal adjustments (1) Master clock frequency (27Mhz) Factory set. User adjustment not recommended.
Input levels
Composite Video 1Vpp composite (75 ohm)
S-Video Luminance: 1Vpp, Chrominance: 286mV burst (75 ohm)
Output levels
Composite Video - Same as respective inputs ±3% into 75 ohm
S-Video Y, C - Same as respective inputs ±3% into 75 ohm
Connectors
Composite in/out (2) BNC female
S-Video in/out (2) 4 pin mini-DIN female
Power 2.1mm female coaxial power jack
Horizontal Split Range 0 to 53.3uS from start of active video
More than 98% of visible screen width typical
Vertical Split Range NTSC/RS170: 0 to 485 lines (fully variable in steps of two)
PAL/CCIR: 0 to 585 lines (fully variable in steps of two)
100% of visible screen height typical
Fade Range 100% A image, 0% B image to 0% A image, 100% B image, 256 steps
Difference Range 100% A image, -0% B image to 0% A image, -100% B image, 256 steps
Memory 10M bit per channel, (full frame x 1 each channel)
Time Base correction Digital memory, frame aligned
Time Base window Full frame, infinite for targeted applications
Frame Sync Controller MicroImage designed custom logic
Freeze B Full frame volatile. Remembers until power is removed or unfrozen
Input Filters 3 stage analog anti-aliasing filter
Decoding 9 bit multi-standard digital decoding
Line Lock Digital Phase Locked Loop
Subcarrier Lock Digital Phase Locked Loop
Comb Filter Multi-line 2H/4H adaptive (NTSC composite only)
Processing 8 bit, 4:2:2, ITU-R601 and ITU-R656 standards
Split/Fade Processor MicroImage Video Systems designed digital signal processor (DSP)
Image Enhance 2D peaking
Encoding Full Digital Modulation
Oversampling 4x (54Mhz) output over sampling
Output DACs 10 bit digital to analog converters
Output Filters Digital plus four stage analog anti-aliasing (reconstruction) filters
Output Subcarrier Digitally synthesized from master clock
Master Clock 27Mhz +/- 5PPM (0.0005%)
Subcarrier Frequency NTSC: 3.579545Mhz
PAL: 4.43361875Mhz (PAL B, D, G, H, I standards)
Horizontal Frequency RS-170/NTSC: 15.734Khz typical
CCIR/PAL: 15,625Khz typical
Vertical Frequency RS-170/NTSC: 59.94Hz typical
CCIR/PAL: 50Hz typical
Sync System NTSC, PAL, RS-170, CCIR
Bandwidth 6Mhz typical
Crosstalk 48dB
Gain Match A to B Typically within 2.5%
Temperature
Operating 0° - 40° C (32° - 104° F)
Storage -40° - 60° C (-40° - 140° F)
Humidity
Operating 10% - 90% (non-condensing)
Storage 5% - 95% (non-condensing)
Power
Voltage +12VDC (+10 to +20VDC) , negative ground
(Universal power module included with standard products)
Consumption 230mA typical (2.8W)
Protection Automatic electronic fuse, internal, self resetting
Size 7.60"D x 7.25"W x 1.60"H (193 mm D x 184 mm W x 40 mm H)
including knob and connectors
Weight 1 lbs. 9 oz., (709g)
DTS120150-P5 supplied Universal Power Module specifications.
Designed and Manufactured in the USA by MicroImage Video Systems.
All specifications are subject to change without notice.
All units come with a universal power supply and operation manual.
The PXD310E does not provide power to the cameras.
The PXD310E replaces the PXD310EN & PXD310EP products

© 1995-2004 MicroImage Video Systems, a division of World Video Sales Co., Inc.
All rights reserved.  Specifications subject to change without notice. 10/04/05
Problems with this site? Contact the  webmaster  
w w w .  m i v s . c o m